Weighing Indicator and Controller Bulkhead Mounted OBSOLETE (SMW)

Load Cell Controller
Optional stainless steel enclosure (LSS)
  • Weighing Indicator with large, high resolution LCD display
  • 10V 160mA excitation for up to 6 Load Cells
  • Simple one pass auto calibration
  • 2 Set points, SPCO relay outputs
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Supports MANTRABUS & ASCII
  • IP65 / NEMA4 ABS housing for wall or surface mounting  

This unit is now obsolete. For technical support or repair please speak to our sales team or local distributor.

The SMW load cell display and controller is bulkhead mounted for strain gauge or load cell measurement applications, with analog or digital output and relay set point outputs.

The SMW weighing indicator and controller is a very flexible digital indicator and display system in a bulkhead mounting format, optimised for single or multiple load cell and weighing applications.
The digital architecture offers very easy one-pass calibration and fast setup.

This versatile Weighing Indicator and Controller Bulkhead Mounted module offers options of isolated analogue outputs, latching relays or digital outputs for control or alarm functions.
The RS232 or RS485 options provide for digital communications (including setup) and can support label or ticket printers.

Additional Features
Variable gain input sensitivity from 0.5 to 200 mV/V
Auto tare and peak hold actioned by volt-free contacts
Programmable in-flight compensation for dynamic weighing operations
Six wire input for barrier and cable compensation
AC or DC power supply options

Can be used in conjunction with our LCI load cell failure alarm, which is designed to continuously monitor the condition of individual load cells and activate an alarm when faults in the system are detected, therefore providing increased safety and cost savings onsite for all weighing systems.

Strain Gauge Input The input is of the load cell/strain gauge type. A transducer excitation voltage of 9.6 volts @ 160mA
Compensation by ± sense wires for cable and safety barrier losses down to 3V excitation
Load cell sensitivity is preset via DIL switches to 0.5, 0.8, 1.0 1.25, 1.5, 2.0, 2.5, 3.5, 5, 10, 20, 50, 100 or 200mV/V
Initial offset is no greater than ± 0.15mV (15uV/V) which is cancelled during auto calibration
Zero Temperature Coefficient 0.0005% FSO/ºC typical with 2.5 mV/V sensitivity selected
Span Temperature Coefficient <0.0017% reading/ºC
Excitation 9.6V DC nominal, 150mA maximum
Repeatability ±0.002% reading over 90 days
Display Update Rate Programmer keypad selectable between 0.1 and 25.5 seconds
Display Average Set by programmer keypad, up to 64 standard up dates
Measurement Resolution 1:32,000

 Analog Output

Type 4-20mA and 0-10V
Drive 4-20mA up to 1Kohm and 0-10 volts up to 2mA


Accuracy 4-20mA + 0.15% of range, typical. 0-10V ±2% before calibration


Resolution as for display up to 13 bits/4.5 digits. Settling time 350mS to within 1% of step change.
Isolation ±130V RMS or DC max to analogue input or any other port
Fast Analog Output  For use with the UAFLC (FAST INPUT OPTION)


Power Supplies 
LS1 110V-120V AC or 220/230V AC 50-60Hz 10W
LS3 9-32V DC 10W isolated
Data Retention/Protection
Retention 10 years for set up values, minimum of 100,000 write cycles.


Protection of Data and Function(s) Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out.
Other Options & Accessories 
2 Set Points Output through 5A, 230V AC SPCO relays, with programmable latching inversion, hysteresis, In Flight (RL1)
Communications Port


For data transfer or print via :-
20mA Loop Enabling up to 254 units to be multi dropped to 1 x RS232 via IF25 interface(s)
RS485 Enabling up to 25 units to be multi dropped
RS232 For 1 to 1 connection or standard printer drive


Printer Operation By front panel function key
Baud Rates 300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)
DIN Rail Mounting For the motherboard


DC Powering 9-32V DC


Remote Mounting Display module, for panel mounting
Back Lighting For the LCD display
Storage Temperature -20 to +70ºC
Operating Temperature -10 to 50ºC
Relative Humidity 95% maximum non condensing
CE Environmental Approvals European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC


  • product logo
  • product logo
  • product logo

Display for strain gauge or load cell weighing systems and applications with easy one-pass calibration and fast setup, offering large high resolution LCD display


No relevant software available

Product order options

SMW Code
A PCB with load cell input, CPU & 4-20mA/0-10V Analogue Outputs with LCD display module & AC power supply 110/120 V or 220/230V SC0001S000 OBSOLETE
Weighing Indicator with Analogue Data & Relay Outputs (OBSOLETE)

Weighing Indicator with Analogue Data & Relay Outputs (OBSOLETE)

High Resolution Weighing Indicator & Controller OBSOLETE

High Resolution Weighing Indicator & Controller OBSOLETE

Q: LCA20 / SMW can they handle tension and compression?

A: Yes

For more 'Frequently Asked Questions' please see our Knowledge Centre

Click here

Contact Us
e-Newsletter Sign Up

Keep up to date with our latest products, news and special offers