Weighing Indicator Controller with up to 16 Set Points (ADW-SP16)

Weighing Indicator Controller with up to 16 Set Points (ADW-SP16)
  • Up to 16 setpoints, each with an associated SPCO relay (on DIN rail module)
  • Individual set point, In-flight and hysterisis values
  • Programmable from the ADW keypad
  • Relay contact rating 230V @ 5A AC
  • Communications and Printer Driver
  • Simple one pass auto calibration for minimum set-up time on site
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Variable gain input sensitivity from 0.5 to 200 mV/V
  • 6 wire input to compensate for zener barrier and cable losses
  • RS232 or RS485 communications for setup, data transfer or label / ticket printing

The DIN rail mounted remote relay units offer an increased number of set points over that provided by a standard ADW15 strain gauge indicator/controller.

This allows for multi-action operations such as batch and recipe control.

The software of the ADW-SP16 gives the user freedom to program the number of set points for their requirements. A single ADW-SP16 will control up to 16 set points, programmed from its front panel.

Set points can be individually set up with In Flight compensation and hysteresis values.
Separate 'Output Latch' and 'Output Action' for up to 14 of the 16 set points is available, adjustable from the front panel of the ADW-SP16. A special mnemonic allows the user to specify the number of set points to be used.

All relays are pluggable and connections are made via field screw terminals.

Inputs
Calibration Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected
Auto Tare By pressing keys ' > ' and then 'R' , display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on powerdown.
Sensitivity Preset via DIL switches between 0.5 to 200mV/V
Excitation 10V DC nominal, 150mA maximum
Compensation By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply
Accuracy 90 days ± 0.08% of reading ± 0.05% of FS typical
Drift 0.002%ºC typical @ 2.5mV/V
DC Analogue Outputs
DC Voltage 0 to 5V, 0 to 10V, -10 to +10V, Max Current out 50mA
DC Current 0 to 1mA, 0 to 20mA, 4 to 20mA, Max Voltage out 20mA
Accuracy typical ± 0.08% of output, ± 0.08%FSD
Resolution as display resolution, max 15 bits
Calibration by 15-turn pre sets for gain and offset
Inversion By keypad value
Isolation ±130V RMS or DC max to analogue input or to any other port
Ranging Fully keypad scalable over desired display range
PID Power level, when selected = 12 bit resolution output
The Relay Output Module
The module consists of 8 relays rated at 230 volts 5 Amps - SPCO, Alarm via 30V 50mA NC contact, DIN rail mounted for a G or top hat profile. Each relay is plug-able and connections are made by 2.5mm field screw terminals.
Indication of relay status is shown by LED's. Trip points volt free contact. The module can be situated up to 2 metres from the ADW15 load cell indicator controller.
Communication Port CP Operation
All display data can be accessed via the communications port along with relay, PID power and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset.
Type Details
RS485/422 For up to 32 instruments on 1 bus, 4 wire, Protocol supports up to 254
RS232 For up to 25 instruments per interface, 4 wire
Cable Length 1km (depending on baud rate)
Baud Rates 300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)
Electrical Isolation ±130V RMS or DC max to analogue input or any other port
Formats MANTRABUS and printer output formats
Power Supplies
220V-230V AC 50-60Hz 10W, 110V-120V AC 50-60Hz 10W, 9-32V DC 10W isolated
Base ADW15
Displays 7 segment LED 4.5 digit 10mm.3 x 3mm LED's 2 for relay status, 1 for program and hold indication
Controls
4 membrane panel keys with tactile feedback. 1 scroll key to view/update parameter. 1 digit select key. 1 digit increment key. 1 reset key. Keypad disable by internal links behind front panel. Hold function by digit select key when in input mode.
Data Retention/Protection
Retention 10 years for set up values, minimum of 100,000 write cycles.
Protection of Data and Function(s) Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out.
Environmental
Storage Temperature  -20 to +70ºC
Operating Temperature  -10 to 50ºC
Relative Humidity  95% maximum non condensing
CE Environmental Approvals European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC

 

  • product logo
  • product logo
  • product logo

Set point controller load cell with in-flight & hysterisis values easy programming from the keypad

 

Software

No relevant software available

Product order options

Please read the following before selecting the options for this product:

ADW15 fitted with Special Edition 16 Set Point Software with remote Driver MOdule to operate 4,8,12, or 16 relay remote DIN Rail mounted modules as required.

Starting with the base model ADW-SP16, select the options that you need to configure the device to meet your needs.

Base Unit Code
ADW-SP16 ADW-SP16
Outputs Code
Analogue Output 0-10V V4
*Limited stocks* Analogue Output 0-1mA A1
Analogue Output 4-20mA A3
Comms Code
RS485/232 Communications for MODBUS RTU, ASCII MANTRABUS COM 1
Power Supplies Code
110V, AC 50/60 HZ 110
230V, AC 50/60HZ 240
Supply 12/24V DC 12/24
Mounting Code
Panel Mount P
DIN Rail D
Accessories Code
Din Rail Mounted 8 Relay Module REM8
4 relay unit REM4
Remote Power Supply Unit 110V or 230V AC ( this unit is only required when operating more than 4 relays ) REM PSU
REM to REM interconnecting cable. Required for each additional REM 4/8 unit REMC2
Batch Weighing Controller, 12 Ingredients or Components

Batch Weighing Controller, 12 Ingredients or Components

ADW-BW
Weighing Indicator/Controller for Loss in Weight

Weighing Indicator/Controller for Loss in Weight

ADW-LW
Weighing Indicator | Controller for Fast Fill Operations

Weighing Indicator | Controller for Fast Fill Operations

ADW-FFW
Contact Us
e-Newsletter Sign Up

Keep up to date with our latest products, news and special offers